Category: ADSL Modem Settings
3Com OfficeConnect ADSL 11g - Quick Setup Guide
This Article has been written to assist users configuring a 3Com OfficeConnect for the first time, this is the most basic of configurations to allow access to the Internet.
Once you have connected the device to the telephone line and your local network via an ethernet cable browse to http://192.168.1.1/
You will be prompted for the System Password. The default is admin, if this is your first time visiting this screen.
Once logged in to the router, click the Wizard tab to start the setup process.
You are first asked to change the router's admin password from the default of admin. This is highly recommended as default passwords can easily be found on the Internet. Once changed to something you can remember, click Next.
Entering the above values will ensure router logs always have the correct date and time.
sahara Internet uses PPPoE for it's ADSL connections. Choose this then click Next.
The default LAN settings should need no changes for the majority of setups. ClickNext
On the wireless settings page choose which channel you wish to use. If you have problems with your wireless connection dropping, it may be due to interference. Try changing the channel if this happens to you.
Click Next one final time to be presented with a list of the settings to be applied.
If you are happy with the information entered, click Apply. The settings are saved to memory and the router will reboot. This will typically take about 2-3 minutes to complete.
Author: Sahara Net.
Entering the IP address to access the modem
Entering the Billion access details
The Billion status page
Saving the Billion configuration
Confirmation of saved settings
Your Billion router should have now connected to the Internet. If you get a message advising that the connection has failed, repeat the above steps, ensuring the settings are all correct.
Author: Sahara Net.
Open your preferred web browser, e.g., Internet Explorer, Mozilla Firefox, etc.
Enter the following number into the address bar: 192.168.1.1 (this is known as an IP Address)
The DSL-2640T is an ADSL Router ideal for home networking and small business networking. The setup wizard will guide you to configure the DSL-2640T to connect to your ISP (Internet Service Provider). The DSL-2640T's easy setup will allow you to have Internet access within minutes. Please follow the setup wizard step by step to configure the DSL-2640T.thin click Run Wisard.
Welcome Wizard Page
Welcome to the DSL-G604T Setup Wizard page. The Wizard will guide you through these four quick steps. Begin by clicking on Next.
Choose Time Zone
Select the appropriate time zone for your location and click Next to continue.
Select Internet Connection Type (WAN)
Select the connection type to connect to your ISP. Click Next to continue.
Set PPPoE / PPPoA
Enter your Internode Username in the format username@Speed.sahara.net.sa It is important that your username includes @Speed.sahara.net.sa or you will be unable to connect.
Enter your Internode Password.
VPI = 0
VCI = 35
Enter the PPPoE/LLC information provided to you by your ISP. Click Next to continue.
The Setup Wizard has completed. Click on Back to modify changes or mistakes. Click Restart to save the current settings and reboot the DSL-G604T.
Author: Sahara Net.
Logging into the Linksys router
Configuring your ADSL Connection
Wireless Configuration for Linksys WAG54G Routers
This guide is suitable for Linksys WAG54G routers.
What we'll cover:
You will need to connect your computer to your Linksys WAG54G with an Ethernet cable to complete the wireless setup.
Logging into the Linksys WAG54G router
Configuring your Wireless Connection
Creating a network name (SSID)
Your network name is used to identify your wireless network. This is particularly useful if there are other wireless networks nearby.
Because your network name will be visible outside of your home or office, the name should be recognisable but should not use any personal or service details.
Creating a Pre-shared Key (Wireless Password)
A Pre-shared key prevents people you don't know from accessing your wireless network. When you connect your computers to your wireless network, you will be asked for the pre-shared key. If someone tries to connect without the pre-shared key, they will be unable to connect.
Your pre-shared key:
We recommend you create a complex password for your pre-shared key.
Congratulations! You have successfully configured the wireless settings on your Linksys WAG54G router.
Author: Sahara Net.
step 1 – connect the router to the Internet
At this point during the installation you’ve established that your computer is speaking to the router and that the router can detect a broadband signal through your telephone line.
You now need to get your router to connect to the broadband signal that is being sent to your telephone line.
3.A log in window (similar to the one below) will prompt you to log into the router’s admin pages – enter the details below:user name: adminpassword: password
The Netgear SMARTWIZARD admin pages will open:
Click Apply and wait for the page to refresh.
Step 4 - set up wireless security
You now need to set up the wireless security settings on the router. Ensure you make a note of the details you choose as you will need these to set up the wireless connection or connect wirelessly to your router.
Secure Your Wireless Network: WPA/WPA2 (Recommended)
This article explains how to configure WPA/WPA2 encrypted security on NETGEAR wireless routers. It can also be applied to NETGEAR access points.
Wireless Settings Screen:
Author: Sahara Net
Logging into your NetComm Wireless NB604N
Configuring your ADSL connection
Congratulations! You have successfully configured your NetComm router's ADSL connection. Close the NetComm configuration page and confirm that you are able to browse the Internet.
Author: Sahara Net - Support
Speed Touch v.585
Open new page in your browser and type this IP
IP : 10.0.0.138 or 192.168.1.254
and follow below steps
Author: Yasser Abdullah Ajaj
How to configure PPPoE on TP-LINK ADSL Modem Router
Step 1 Open the web browser and type the IP Address of the device in the address bar (default is 192.168.1.1) then press Enter .
Step 2 Type the username and password in the login page, default username and password are both admin in lower case, then click OK to log into the device.
Step 3 Click Quick Start on the upper side.
Step 4 Click RUN WIZARD and click NEXT to configure the ADSL Router.
Step 5 You may change the admin account password by entering in a new password. If you wouldn’t like to change, type the default password and click NEXT.
Step 6 Select the correct Time Zone and click NEXT.
Step 7 Select PPPoE/PPPoA and then click NEXT.
Step 8 Input the Username and Password provided by your ISP. Input correct VPI = 0 and VCI = 35 which also are provided by your ISP. Then click NEXT.
Step 9 If your ADSL Router supports wireless function and you want to connect to it wirelessly, please set Access Point Activated and configure the security. Here we take WPA-PSK, TKIP/AES as example. Type in your key and click NEXT.
Step 10 Click NEXT and Close to save the settings.
How to reset TP-LINK products to factory defaults(Forgot/Lost Password)
Note: If you reset the device, the device will return to factory defaults, you will lose all your settings.
1. By pressing the RESET button on the rear panel.
Step 1 Turn off the modem (pull the power out of the unit ).
Step 2 Press and hold the reset button on the rear panel with a pin, while holding down the reset button turn on the modem (plug the power back into the unit). It is important that you continue to hold down the reset button for approximately 15 seconds.
Step 3 Release the reset button and wait for the device to reboot.
2. By using Web-based Utility.
Step 1 Open the web browser and type the IP address of the wireless router in the address bar (default is 192.168.1.1). Press Enter.
Step 2 Type the username and password in the login page, the default username and password both areadmin，then click OK to connect to the device..
Step 3 Click Management->Settings->Restore defaults on the left side, and then click Restore to reset the device to factory defaults.
1. Make certain that the router is powered on before it restarts completely.
2. The default IP address is 192.168.1.1, and the default login username and password both are admin (all lower case).
3. Ensure that the IP address of your computer is in the same subnet with the device. It means that your computer should have an IP address 192.168.1.X (X is in range of 2~253), and the subnet mask is 255.255.255.0, the default gateway should be 192.168.1.1 which is the IP address of the router.
Author: Sahara Net
The quick setup feature is a simple way to configure the gateway with the most important settings. If you did not configure the gateway in EasyConfigurator, the following window appears automatically the first time you open the gateway's Web user interface (by opening the address 192.168.1.1). It also appears if you reset the gateway to its factory defaults:
To begin the quick setup, click Start.
Step 1. Configuring the Internet Connection
This is the first quick setup page:
In this page, you can set up the gateway's connection to the Internet. The most important settings are the connection protocol PPPoE, VPI:0/VCI:35 values, and various parameters specific to the connection protocol, such as a login user name and password. Your Internet Service Provider should be able to supply you with most of this information.
When you are done entering data in this page, click on Next.
Step 2. Wireless Network Name and Security Settings
This is the second quick setup page:
The gateway can be configured to continuously transmit the network name, so setting a meaningful name will helps you configure wireless communications with your computers. You will probably want to replace the default network name that appears in the top half of this page.
U.S. Robotics strongly urges you to select the Secure the gateway... checkbox. The Pass phrase is text you will need to enter if you wish to further configure your gateway's security. It's similar to a password, and you should enter a phrase that would not be easy to guess but that you will be able to remember.
Click Next to continue.
Step 3. Gateway Login
When you open the gateway's Web User Interface to work with the gateway settings, you will need to log in with a user name of admin. In this page, enter the password you want to use with this admin account..
Enter a password and click Next.
Step 4. Wrapping Up
You are now nearly done with the quick setup process. Click Finish to save your configuration to the gateway.